My first extraction. ACRB freeze/thaw/shred/vinegar-simmer, salt, base with lye, toluene, stir. See attached pics. First 2 pics are after sitting for an hour. Toluene is clear. When I stir it, it turns yellow (3rd pic), but then the color just "drains back down" into the soup (4th pic). I can see that a reddish film sticks to the glass but then drains down also. Then it's nearly clear, with a slight reddish tint to it. I tried stirring it and some red film stuck to the stainless steel stirrer. I'm not sure what the lid to my bottle is made of, so I'm afraid to get the toluene on it, so I am not inverting it, but rather rolling it to get the soup spinning. Please help, thanks! dogsoldier attached the following image(s):  20190620_093805.jpg (3,237kb) downloaded 92 time(s). 20190620_093824.jpg (2,496kb) downloaded 89 time(s). 20190620_093859.jpg (2,920kb) downloaded 89 time(s). 20190620_093958.jpg (2,424kb) downloaded 87 time(s).
|
|
|
There is no relation between color of solvent and what it contains.. Chemistry is in your favor, the principles simply work, reliably, so if you have a basified solution containing dmt and your non-polar solvent is mixed, you can be sure your dmt will move to the non-polar solvent. Just proceed. dogsoldier wrote:My first extraction. ACRB freeze/thaw/shred/vinegar-simmer, salt, base with lye, toluene, stir.
See attached pics. First 2 pics are after sitting for an hour. Toluene is clear.
When I stir it, it turns yellow (3rd pic), but then the color just "drains back down" into the soup (4th pic). I can see that a reddish film sticks to the glass but then drains down also. Then it's nearly clear, with a slight reddish tint to it. I tried stirring it and some red film stuck to the stainless steel stirrer. I'm not sure what the lid to my bottle is made of, so I'm afraid to get the toluene on it, so I am not inverting it, but rather rolling it to get the soup spinning.
Please help, thanks!
|
|
|
endlessness wrote:There is no relation between color of solvent and what it contains.. Chemistry is in your favor, the principles simply work, reliably, so if you have a basified solution containing dmt and your non-polar solvent is mixed, you can be sure your dmt will move to the non-polar solvent.
Just proceed.
Thank you! Also, update: I shook the heck out of it for 30 seconds, and it definitely settled out yellow. But I am still freaked out about the lid, since I looked up and found that many lids are made of HDPE, which is immediately damaged by toluene. So I think I will stick with the stainless stirrer for my subsequent pulls.
|
|
|
Hi. Just wanted to say I hope it goes well, exciting times for sure. Connor Reality is a simulation, what lies beyond is too complex to fully comprehend.
|
|
|
Connor137 wrote:Hi.
Just wanted to say I hope it goes well, exciting times for sure.
Connor Thanks man! I have the vinegar wash evapping now! Looks like I will have to finish it tomorrow, but it looks like I will at least get something in the end!
|
|
|
You could maybe use cork, or see if a metal growler cap will fit that vessel. I might even be tempted to just put my thumb over it. Better than plasticizers...just saying. Sine experientia nihil sufficienter sciri potest -Roger Bacon
*γνῶθι σεαυτόν*
|
|
|
null24 wrote:You could maybe use cork, or see if a metal growler cap will fit that vessel. I might even be tempted to just put my thumb over it. Better than plasticizers...just saying. I thought about a cork, but I thought I might loose product because it would soak into the cork... But I wonder which would be more likely to go into the cork : toluene or aqueous base?
|
|
|
Sometimes I use room temp or very slightly heated solvent (naphtha) and it's clear - but contains as much actives as expected. A quick test is to lest a small amount evaporate on a watchglass.
|